Installing a boost controller

Hi chaps need some help in finding out which wires on the ecu harness are for the following

1) vehicle speed

2) rpm

I have a boost controller that I'm trying to install I'm hoping someone can point me in the right direction

Thanks

Pin #
Name
Function
Signal Type

2
Tachometer Signal
Engine Speed Sensor Signal
Speed

4
Main Relay (Electronic Concentrated Control System)
12V Switched
Power

6
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

13
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

16
Mass Air Flow Sensor
Mass Air Flow Sensor Signal
Analog

17
Mass Air Flow Sensor Ground
Chassis Ground
Ground

18
Engine Coolant Temperature Sensor
Engine Coolant Temperature Sensor Signal
Analog

19
O2 Sensor Signal
Oxygen Sensor Signal
Analog

20
Throttle Position Sensor
Throttle Position Sensor Signal
Analog

21
Sensor Ground
Chassis Ground
Ground

26
Air Temperature Sensor
Air Temperature Sensor Signal
Analog

27
Knock Sensor
Knock Sensor Signal
Knock, Audio

29
Sensor Ground
Chassis Ground
Ground

32
Vehicle Speed Sensor
Vehicle Speed Sensor Signal
Speed

36
Ignition Switch
12V Switched
Power

39
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

46
Power Supply (Aux)
12V Permanent
Power

47
Power Supply (Engine Control Module)
12 Switched
Power

48
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

101
Injector # 1
Engine Speed Sensor Signal
Speed

103
Injector # 3
Engine Speed Sensor Signal
Speed

107
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

108
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

109
Power Supply (Aux)
12V Permanent
Power

110
Injector # 2
Engine Speed Sensor Signal
Speed

112
Injector # 4
Engine Speed Sensor Signal
Speed

116
Power Ground (Electronic Concentrated Control System)
Chassis Ground
Ground

Thanks stu seen this aswell just unclear as to which is the rpm and a couple of different 'vehicle speed' pins about.

The installation manuall does not specify which one.

Any further clarification is appreciated.

What e.b.c is it indy ???

It's a blitz icolour spec r Leighton.
I've been reding the online installation manual, but because I'm a retard I can figure out where the rpm and vehicle speed wire is.

Chuck up the link to it mate ....see if we can work it out ...

Here you go

http://97supraturbo.com/Manuals/SBC%20i-Color%20Eng.pdf

Page 18 instruction 5

Just need to find out what wires to splice into loom

Thanks in advanced for you help guys

I've still got these wires marked on my loom at home, I could have a look for you tonight if it's not sorted by then mate.

https://s244.photobucket.com/user/josamoga/media/SR20DET%20Project/ECU-pin-outB13.jpg.html

Does that help mate??

Pin 2 is RPM

Pin 32 is vehicle speed

That would be nice of you woody .... i would of said 2 and 32 ....

Spot on spike .... looks like i was right

Great chaps thanks for all the help ( I love this forum and the people on it)

Gonna go and start splicing and soldering
Wish me luck

Mr woody if you have time that would be wonderful if you could sorry for being a pain in the bum bum

That's alright mate. Just so you know it's morning here so wont have an answer for another 10 hrs

In the interim I agree with the above btw

Lol that's fine I'm gonna go bed now and will carry on tmw morning!

Hello chaps the diagram that's been put up in the earlier post is that a pin out from the ecu or a pin out from the harness thanks

Its a pin out for the ecu me thinks

Ah ha so so I'm assuming pin 2 will be on the right hand side of the harness and 32 will be on the left of the harness

God I'm a think poo

Ok so I had:

Rpm - blue/ black stripe
Speed - yellow/ green stripe

Do these colours match up to pin 2 and 32?

Thanks mr woody I will double check now

Let me know how you get on, I know for a fact that was what I was using for rpm.

Just checked not the ones you mentioned mr woody

If only I knew how to put pics up

That's terrible news, no idea. Maybe mines been butchered over time..