Gtir Motorsport club
Would you like to react to this message? Create an account in a few clicks or log in to continue.
Gtir Motorsport club

Welcome to the largest Nissan Pulsar & Sunny GTI-R Forum. Masses of info, friendly members, cars for sale, lots of spares. Best forum on the net by far. Everything your gtir needs is here.


You are not connected. Please login or register

help needed

+4
BEBB GTIR
GTIR James
Gtirchris
Digitalfaze
8 posters

Go down  Message [Page 1 of 1]

1help needed Empty help needed 5th January 2014, 11:02 am

Digitalfaze

Digitalfaze
web admin
web admin

how do i get wires to my engine bay, i can see where the come into engine bay but cant access that area from inside the car took glove box out and tried to get my hands in but no luck, do i need to remove everything from behind glove box?

also erm where is the ecu located  Embarassed 

http://www.avaloncreative.co.uk

2help needed Empty Re: help needed 5th January 2014, 12:19 pm

Gtirchris



Hey buddy, the ecu is located behind the heater control panel, it is bolted to the floor on the tunnel, if you take off the plastic trim next to the footrest you will see it, also you will need to remove the trim on the other side, the wiring loom for the ecu goes through the bulkhead, follow it from the ecu and you will see where. The other loom for the lights etc also goes through the bulkhead near the left hand suspension turret,if you take the glove box out you should be able to see it up behind the heater box,hope that helps mate. Wink 

http://www.guglielmimotorsport.co.uk

3help needed Empty Re: help needed 5th January 2014, 12:42 pm

Digitalfaze

Digitalfaze
web admin
web admin

Perfect thanks very much ill try again Smile on the left hand turret where the gauges etc go through bulk head i cant seem to get to the hole, its blocked by the air con box thing, i also tried removing that but no luck

http://www.avaloncreative.co.uk

4help needed Empty Re: help needed 5th January 2014, 1:55 pm

GTIR James



Remove the heater box buddy. Think there's a few screws & a few 10 mm bolts

5help needed Empty Re: help needed 5th January 2014, 4:44 pm

Digitalfaze

Digitalfaze
web admin
web admin

is that the one on the left or right? i read one of them is the aircon unit and if you still have ac installed you cant remove it, i couldnt get it to budge after removing all the screws

http://www.avaloncreative.co.uk

6help needed Empty Re: help needed 5th January 2014, 4:56 pm

BEBB GTIR

BEBB GTIR
the one star club
the one star club

If you take the offside (righthand) wheel off then remove the arch liner youll see all the looms and hoses running along the top, they then go through a rubber bung into the cabin, once in the cabin the wires are located above the accelerator peddle.

7help needed Empty Re: help needed 5th January 2014, 4:58 pm

Digitalfaze

Digitalfaze
web admin
web admin

ok thanks ill try that out, didnt realise it would be this much trouble

http://www.avaloncreative.co.uk

8help needed Empty Re: help needed 5th January 2014, 5:13 pm

pulsarmoley

pulsarmoley
moderator
moderator

I drilled a hole through the bulkhead behind glove box and fed the wires through a rubber grommet for protection as it was easier.

9help needed Empty Re: help needed 5th January 2014, 5:55 pm

nomad

nomad
Admin
Admin

I ran most of my new wiring through the rubber grommet just behind the abs pump top right corner passenger side it was abit tight but it drops behind the glovebox .

10help needed Empty Re: help needed 5th January 2014, 11:55 pm

buckym120

buckym120

As above the rubber grommet below the abs pump

11help needed Empty Re: help needed 6th January 2014, 7:27 pm

Digitalfaze

Digitalfaze
web admin
web admin

managed to get it done, so much easier going via the drivers wheel arch, quick question when fitting the avcr, i remove the restrictor hose and run a pipe from plenum to avcr, then another from avcr to the turbo then remove and block off the pipe which goes to intake pipe? (in theory just puting the avcr in the middle of the pipe going from plenum to turbo?), so which ports on the avcr do the pipes go into?

also the pipe going from back of block to dumpvalve i just cut it and instert a t-piece which goes off to the map sensor?

Thanks in advance just wanna make sure im doing it right



Last edited by Digitalfaze on 6th January 2014, 7:35 pm; edited 1 time in total

http://www.avaloncreative.co.uk

12help needed Empty Re: help needed 6th January 2014, 7:33 pm

nomad

nomad
Admin
Admin

I havent got an avcr ....does it have a boost soleniod ?

13help needed Empty Re: help needed 6th January 2014, 7:47 pm

toaster55

toaster55

have you got the manual? if not heres a link, should have it in there some where
http://www.type-ra.com/pdf/AVC-R_manual.pdf
hopefully help you as this is what i used to fit mine. or to make it easier the one that says COM on the valve goes to your wastegate actuator the other that says NO goes to the plenum. good luck  Smile oh and your dump valve one is right you just tee it off.

14help needed Empty Re: help needed 6th January 2014, 8:26 pm

Digitalfaze

Digitalfaze
web admin
web admin

yeah it has everyhting with it, got it all setup today just not connected everything up yet as i wanted to make sure i done it properly, didnt come with a manual only a manual for the ecu wiring which im ok with doing.

yeah it has its own solenoid and a map sensor for reading boost pressure

http://www.avaloncreative.co.uk

Sponsored content



Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum