CV Boots

^ that not good response from ICP

You right that both they sent out are same spec just different brand & are outer boots so deffo not right/workable for the inner .
I would go to local factors & get the ADN18167, you could take clean joint to test.
If you do want try a ADN18167 I'll pay you price of one if don't fit/you out of pocket, matches fine on parts data base to the nissan inner boot part number & I would like see it confirmed one way or the other .

Ive ordered them before, cheers for the offer though mate. Will post up and let you know tomorrow.

hoping for pleasing fit lol .

surprised ICP been that blunt useless :-/ very poor effort on their behalf ...

I thought that, ordered a lot from them over the last couple of months.. Oh well. Do the rear outers fit the front outers?

^ Yes as what you got is all front outer spec, ADN18111, N116007, FCB2062 all same same.
I've used ADN18111 & N1116007 on front outers, I also used ADN18111 on rear outers as they fit well & when doing cross match for rear outers the ADN18111 is closest available match to rear outer oem nissan boot I could source easily .

Got them, Hoping to fit them tomorrow if I get chance..

Good you got it sorted. I ordered 2 rear inners from eBay, but they only had 1 so now I've got to get another grrrr.

@burrows
think I would of been out in my pyjamas doing a quick test fit, how will you be able sleep lol .

@woody
what make & part number did you get woody ...

I ended up getting a Ashika 63-00-012. Might need to use another brand for the other side though.

^ that boot closer rear outer than a rear inner

Crap, maybe its the outer then. I've got 3 boots at home. So Ill check which part number the other 2 are. Maybe it's another rear outer I need.

Mr B wrote:@burrows
think I would of been out in my pyjamas doing a quick test fit, how will you be able sleep lol .

@woody
what make & part number did you get woody ...

The wife stopped me First job in the morning though!

Perfect fit Mr B, even got a ridge inside the boot the fits into the recess on the cv.  





Gaz

The blueprint boots generally are little better in terms of to oem spec/size & decent groove lips.
SolidAuto are nice boots too & slightly better cost but no good if ICP not supplying right fit ones,
I'll mark up the ADN18167 as test fitted 'approved' by you in the first post .

Other 2 boots I have are 0215-jp16 so all good just another rear outer I need B.

^ that Febest 0215-jp16 looks spot on size, same size in product specs as the adn18167.
Febest friendly pricing too .

They were very well priced from memory. Much better than some of the other boots I went looking for.

Interesting read, I cant seem to get them priced up for under 60 though lol

P.s Mr B Rep point Given as you also saved me a shit load of work Thanks bud.

This thread is like the holy grail for cv boots

On pricing :
the front trilobe boot ADN18141 can be had for under £10 from eurocar parts
http://www.ebay.co.uk/itm/Inner-CV-Boot-Kit-Fits-Nissan-Elgrand-Skyline-NP300-Pick-Up-/231278127239?hash=item35d9402887
You best trying local one or there online site as price should get better plus if don't buy straight away they normally email people 10% discount codes. they should have other boots too.
front & rear outers can be had for under £5 each (all same boot model, firstline brand cheap)
Used the Febest boot that Mr Woody found for rear inners as they cheap price & you can build full set up for under £60 easily .
Using all blueprint probably going be fair bit more unless Euro car parts do very good pricing on them all or you friendly with local factors !

I'm just glad I don't need to get that bastard spider assembly off again or that long bolt on the rear axel

That new long bolt will come out easy :-D

When I replaced the rear inners I took the whole driveshaft out. Just a tip, I couldn't get one side back into in the diff. So I had remove inner boot (that I just assembled) hit the joint in and refit the boot. Was annoying